The Way to Have your Garage Door Opener Installed

Do you already have an applied door opener in your garage? Do you think of finding some substitute for it? What you need is to take all components down and discard all of them. Tossing out the old switches, remoting and evening the wiring (but not in the case it is on top of the drywall of the garage) are necessary. In most of cases your just bought opener will come with all new parts including wall switch, 2 remotes and possibly even an exterior mounted switch with buttons allowing you to put your own password and open and close the door of your dwelling garage.

This is the best suitable capability for your children, especially when they are back from school and want to get into the house. This position is connected with electronic coding that is oftenly built in. The system works in such a way: electronic coding changes the code sent from your remote to the door opener unit in the garage each time you take advantage of this possibility.

Now, you are to check if all the parts necessary for this are present in the just sent package. Put all the parts in packages seperately and now be sure to READ the instructions. They will certainly help you not to waste that much time.

The first thing to concentrate on is collecting the track. In most cases it is sent in three sections. There is no much trouble in assembling and hooking to the front of the opener. Be attentive now and be sure to follow your specific instructions.

One of the most possible next steps you will have to do in the process of direction reading is to raise the door opener to the ceiling of your garage.

For that you will have to use 7 foot step ladder. With a help of it you will keep the opener in the approximate place in the process of anchoring designing that is demanded. It happens that It is including a simple rubber mechanism between the mounting hardware and the drywall is one of the possible things right at this situation. If you do this procedure right this will bring a great result in the form of possible vibration reduction. Attach the "door end" of the opener to the door header (usually 2 x 12 or something similar) that is above the entire length of the garage door. For this lag bolts are usually necessary. This is the time proper for installing the chain or the belt that moves when the door opener motor turns a sprocket on top.So, you are finishing this project. You may rest as soon as the most difficult job is already done. Now you need to lead the wire (if it isn't installed yet) from the opener to the interior switch. In the most modern switches radio signals are used, so depending on the situation this process may be not fullfilled. You need to check in directions if this is essential. You will find a wiring diagram that is common in the following picture.

In the package with the door opener you will also find two electronic sensors. You are to apply them near the bottom of the garage door adjacent to the garage door track. The purpose of them is "looking at" each other to send a message to the opener that it is safe to close the door. Remember that if something is within the invisible stream of light passing from one of these to the other, then the door will NOT close. This is a kind of a security system necessary on the condition that little kids or small pets may be standing where the door will close and to avoid injuries. There is one more wire attaching

from each eye that is to be applied all the way to the opener. Be sure to follow certain directions included on how high to lift and how to lift these safety devices. Do not ignore this step as the door opener will NOT run if these are not hooked up and aligned in the right way. Working together they fullfill the function of safety device for the door. The next step is to apply batteries into each remote keeping to the instructions once again. Plug the unit into an outlet and don't forget to try it several times.

The situation of adjusting a new opener is widespread. It is not about your wrong actions in the process of installing. It depends on the weight of doors and also on the strength of springs. Be sure to do everything as in the instruction again and adjust the "down" or "up" tension and travel screws by turning them right or left 1/4 turn at a time until you get the door to stay shut or open all the way.

If you think this ideas, the so called "E How To" helpful, it would be great to know your positive opinion. I could write other articles that I hope will assist people. So please let me know your attitude.

You are to measure the height of the garage door opening after applying a new opener. This factor may become crutial if you are willing to park a van or other full size vehicle in your garage. The possible clearance may be not suitable. You shouldn't try to exclude the electronic eyes when installing a new opener. It will function only when aligned right.


Write Me: mail@promoredex.com

Latest Posts: